![]() ![]() For this purpose use the drain hole cleaner provided with the appliance (available also in our Webshop).ĬAUTION! Never use sharp metal tools to scrape off frost from the evaporator as you could damage it. It is important to periodically clean the defrost water drain hole in the middle of the refrigerator compartment channel to prevent the water from overflowing and dripping onto the food inside. The defrost water drains out through a trough into a special container at the back of the appliance, over the motor compressor, where it evaporates. Refer to the "Hints and Tips" chapter in your user manual.įrost is automatically eliminated from the evaporator of the refrigerator compartment during regular use. Make sure that there is cold air circulation in the appliance. There is no cold air circulation in the appliance. Refer to the "Coolmatic function" section in your user manual Refer to the "Frostmatic function" section in your user manual The Frostmatic / FastFreeze function is switched on The thickness of the frost is greater than 4-5 mm. Store fewer food products at the same time Many food products are stored at the same time. Let the food product's temperature decrease to room temperature before storage. The food products' temperature is too high. Refer to the "Closing the door" section in your user manual Temperature troubleshooting Possible Cause In any case, press the Alarm reset switch to deactivate the acoustic alarm. When normal conditions are restored the Alarm light stops blinking and the sound turns off automatically.Īn acoustic alarm sounds when the door is left open for around 80 seconds.Īfter closing the door, the acoustic alarm stops. ![]() The sound can be switched off at any time by pressing the Alarm reset switch. due to a power failure) the Alarm light is blinking, and the sound is on. When there is a temperature increase in the freezer compartment (e.g. Turn the temperature regulator counterclockwise to obtain a higher temperature inside the appliance. Turn the temperature regulator clockwise to obtain a lower temperature inside the appliance.Ģ. If you do not press any button, the sound switches off automatically after around one hour to avoid disturbing you. During the alarm, the sound can be muted by pressing any button. If the fridge door is left open for approximately 5 minutes, the sound is on and the alarm indicator flashes. The alarm indicator continues to flash until normal conditions are restored. The freezer temperature indicator shows the highest temperature reached for a few seconds and then the display shows the set temperature again. When there is a temperature increase in the freezer compartment (for example due to an earlier power failure), the alarm and freezer temperature indicators flash and the sound is on.ġ. Inadequate cooling, not cooling enough, temperature too high.The appliance emits an emergency alarm sound or beeps.The fridge display shows a flashing triangle.An alarm is visible on the fridge panel.If you have any questions, please contact us. If you experience any of the following error codes, this could indicate an authorized service is required: Simply open the door and look in the ice chute and remove any blockage. ![]() Refer to your Owner’s Manual to deactivate.ĭI SP – Indicates there is an ice cube(s) jammed in the ice chute for an extended period of time. SB or Sb – Your refrigerator is in Sabbath mode. ![]() Close the door and press the Set key to reset any alarms. If the temperature of your refrigerator reaches 55 degrees Fahrenheit or greater, the alarm will activate.ĭoor Ajar – If the freezer or refrigerator doors have been left open for 5 minutes or more, an alarm will sound and the Door Ajar indicator will illuminate on the display. If the temperature of your freezer reaches 26 degrees Fahrenheit or greater, the alarm will activate. The alarm can be muted but it will stay active (or illuminated) until the temperature resumes normal operation. This is usually caused by inadvertently not closing the door all the way or leaving the door open for an extended period of time. H or HI or High Temp – Indicates the freezer and/or refrigerator section of your appliance have exceeded the temperature threshold. If your power was out for an extended period of time, the HIGH TEMP alarm may also illuminate or alarm until the unit reaches a safe operating temperature. The refrigerator will then resume normal operations. Simply acknowledge the alarm (once power is restored) by pressing “Alarm Reset”. Power Failure or PF – In the event of a power failure, your unit will display Power Failure or PF. For more information, please refer to your Owner’s manual as they may vary by model. Most alarms are designed to alert of you of changes in your or an action on your part is required. ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |